Why Regular Cleaning Matters

The ZXP Series 7 is designed for high-performance printing, but dust, card debris, and ribbon residue gradually build up in the printer’s critical areas. According to the official user manual, regular cleaning maintains your warranty and helps protect hard-to-reach parts like the printhead, transport rollers, and magnetic encoder station.

Recommended cleaning intervals for a typical office environment:

• Card Path cleaning: Every 5,000 cards
• Feeder Path cleaning: Every 5,000 cards

Before You Start: What You Need

Zebra recommends using only approved cleaning supplies. For the Zebra ZXP Series 7, you may need:

• Printer tarjeta de limpieza (long, short, laminator, or polishing type)
• Feeder cleaning card
• Polishing/lapping card (Zebra-authorized only)
• Cleaning wipes or cleaning swabs (for laminator rollers)

How to Initiate the Cleaning Process on the Printer

All cleaning functions are accessed through the Operator Control Panel (OCP):

1. Press MENU on the OCP.
2. Scroll to Advanced Settings.
3. Select Clean Printer to open the cleaning menu.

1. Clean the Card Path (Primary Printer Cleaning)

This is the most frequently required cleaning routine.

Steps:

1. On the Clean Printer Menu, select CLEAN CARD PATH.
2. Follow prompts and prepare your tarjeta de limpieza de impresora.
3. Open the print cover and ribbon drawer, remove the ribbon, then press Next.
4. Insert the tarjeta de limpieza larga into the Manual Feed Slot and press Clean.
5. Wait while the printer runs the cleaning cycle and ejects the card.
6. Flip the card, reinsert, and repeat.
7. Replace the ribbon.

2. Clean the Feeder Path

Cleaning the feeder ensures smooth card feeding and prevents jams.

Steps:

1. Choose CLEAN FEEDER in the cleaning menu.
2. Remove all cards from the feeder cartridge.
3. Insert the short feeder cleaning card into the top slot.
4. Press Clean, then flip the card and run the cycle again.
5. Reload cards into the feeder.

3. Printhead Polishing (Advanced Cleaning)

Printhead polishing is recommended every 5,000 cards, especially when you notice ghosting or faded print.

Note: This feature is password-protected and limited to Zebra-authorized service personnel.

Steps:

1. Enable printhead polishing in the ZXP Toolbox.
2. Open the cover and ribbon drawer; remove the ribbon.
3. Insert a polishing (lapping) card grit-side-up into the Manual Feed Slot.
4. Run the cleaning cycle and wait for the card to eject.
5. Replace the ribbon.

4. Cleaning the Laminator (If Equipped)

The laminator includes three separate cleaning routines:

A. Laminator Card Path Cleaning

1. Select CLEAN LAM CARD PATH on the OCP.
2. Wait until laminator rollers cool below 60°C.
3. Remove laminate cassettes.
4. Insert the laminator cleaning card and press Clean.

B. Laminator Roller Cleaning

Requires cleaning swabs / cleaning wipes.

1. Select CLEAN LAM ROLLERS.
2. Remove laminate cassettes.
3. Use a cleaning swab/wipe to gently clean the top and bottom rollers.
4. Move the swab side-to-side using moderate pressure until rollers stop turning.

C. Laminator Oven (Heater Roller) Cleaning

1. Select CLEAN LAM OVEN.
2. Wait until temperature is below 60°C.
3. Remove four thumb screws and slide out the heater assembly.
4. Insert the hot roller cleaning card between rollers and pull through.
5. Flip the card and repeat before reinstalling the assembly.

Tips for Best Cleaning Results

• Never reuse a tarjeta de limpieza—Zebra explicitly warns against this.
• Avoid high-pressure air compressors inside the printer.
• Only use cleaning supplies designed for the ZXP Series 7.
• Maintain a dust-free environment and store cards properly.
• Always replace cleaning rollers in the dual cleaning cartridge and manual feed cassette when worn.

Recommended MediTech Cleaning Products

MediTech provides high-quality, cost-effective cleaning supplies fully compatible with Zebra ZXP Series 7 printers:

• MediTech Long Cleaning Card (For Card Path Cleaning)
  Ideal replacement for OEM long cleaning cards used in the card path cleaning cycle.
  Recommended for: CLEAN CARD PATH routine.
• MediTech Short Cleaning Card (For Feeder Cleaning)
  Designed for the feeder inlet to remove dust and debris.
  Recommended for: CLEAN FEEDER routine.
• MediTech Toallitas limpiadoras con IPA / Hisopos de limpieza
  Perfect for cleaning laminator rollers, heater rollers, and surrounding components.
  Recommended for: CLEAN LAM ROLLERS and similar manual cleaning tasks.
• MediTech Printhead Cleaning Swab (IPA-based)
  Helps remove debris buildup along the printhead during advanced printhead maintenance.

Tools You Need for Safe Camera Cleaning

Before you begin, gather these essential cleaning tools:

• Soft cleaning wipes
• Air blower
• Lens cleaning solution
• Microfiber cloth
• Sensor cleaning swabs for internal sensor care
• Camera cleaning brush

Using professional-grade tools protects your equipment and prevents accidental damage.

Step 1: Clean the Camera Exterior

Start with the parts that accumulate dirt most often — the body and grip.

1. Power off the camera.
2. Use a soft brush or blower to remove surface dust.
3. Wipe the exterior with a gentle Paño de limpieza or a slightly damp microfiber cloth.

Avoid excessive moisture and never spray liquid directly onto the camera.

Step 2: Clean the Camera Lens

Your lens is the most important surface affecting image clarity.

1. Use a blower to remove loose dust.
2. Gently wipe in circular motions using a microfiber cloth.
3. For stubborn smudges, apply lens solution to the cloth (not the lens).

A clean lens ensures sharp, crisp images without blur or flare.

Step 3: Clean the Camera Viewfinder

The viewfinder can accumulate oil and dust, affecting visibility.

• Use Toallitas limpiadoras to gently clean the eyepiece.
• Avoid pressing too hard to prevent scratches.

This improves the shooting experience and viewing accuracy.

Step 4: Clean the Camera Sensor (Safely)

Sensor cleaning requires caution. Dust on the sensor causes dark spots on photos, especially at small apertures.

How to Clean the Sensor Properly

1. Switch to your camera’s “Sensor Cleaning Mode.”
2. Aim the camera downward and use a blower to remove loose dust.
3. If dust remains, use a Sensor Cleaning Swab designed for your sensor size.
4. Add a drop of sensor cleaning fluid (if required).
5. Gently swipe across the sensor from one side to the other.

Using high-quality Sensor Cleaning Swabs ensures safe and streak-free results.

How Often Should You Clean Your Camera?

• Exterior and lens: once a week or after dusty shooting environments
• Sensor: only when dust appears in your photos
• Viewfinder: as needed

Regular maintenance keeps your camera performing at its best.

Why Cleaning Your ZT411/ZT421 Is Important

Thermal printers like the Zebra ZT411 and ZT421 rely on precise heat transfer. When the printhead or platen roller is dirty, you may notice:

• Faded or missing print areas
• Streaky or uneven labels
• Barcodes that fail to scan correctly
• Frequent label jams or misalignment

Routine maintenance not only improves print quality but also extends the lifespan of your printhead and platen roller — saving you from costly replacements.

Recommended Cleaning Schedule

Zebra recommends cleaning your printer components according to usage:

Tip: Use MediTech’s 99% Isopropyl Alcohol (IPA) Cleaning Swabs for safe, residue-free cleaning. Each swab is pre-saturated with high-purity IPA, ideal for removing adhesive, dust, and ink buildup.

How to Clean the Printhead and Platen Roller

Step 1: Prepare for Cleaning

• Open the media door.
• Allow the printhead to cool (it may be hot after use).
• Power off the printer for safety and discharge static electricity by touching the metal printer frame.

Step 2: Remove Media and Ribbon

• Lift the printhead-open lever upward.
• Remove any loaded media or ribbon to access the printhead surface.

Step 3: Clean the Printhead

• Use a Zebra-approved cleaning swab or a lint-free swab dipped in 99.7% isopropyl alcohol.
• Gently wipe the brown strip on the printhead from end to end.
• Allow the solvent to evaporate completely before continuing.

Step 4: Clean the Platen Roller

• For standard (white) rollers: Rotate manually and clean thoroughly using the same swab.
• For linerless (dark brown) rollers: Do not use alcohol or swabs—lightly touch the roller surface with the sticky side of a linerless label to lift debris.

Step 5: Reload and Resume Printing

• Reload your media and ribbon, close the printhead assembly, and lock it in place.
• Close the media door and press PAUSE to resume operation.
• The printer may feed or calibrate automatically.

Best Practices for Long-Term Maintenance

• Always use high-quality media and ribbons to minimize debris.
• Avoid harsh cleaning agents or abrasive materials.
• Store your printer in a dust-free, temperature-controlled environment.
• Regularly check for buildup in the media path and sensors.

Common Signs It’s Time to Clean

• Barcodes fail to scan correctly.
• Print appears faded, uneven, or has missing sections.
• Labels feed improperly or drift out of alignment.
• “Printhead needs cleaning” warning appears on the display.

When these issues occur, follow the cleaning steps above before seeking service.

Conclusion

Maintaining your Zebra ZT411 or ZT421 printer doesn’t just keep prints looking sharp — it reduces downtime, prevents costly repairs, and extends printhead life. By following Zebra’s recommended cleaning procedures, you’ll ensure your industrial printers operate at peak performance day after day.

Foam swabs are designed to safely remove dust, oil, and debris from delicate surfaces without leaving residue or causing scratches. But with so many types and brands available, finding the right one can be confusing. This blog post will help you understand what foam swabs are, their different uses, types, and factors to consider when choosing the right foam swabs for your electronic cleaning needs.

What Are Foam Swabs?

Foam swabs are precision cleaning tools designed to remove dust, grease, and residue from delicate surfaces. Each swab has a soft foam tip attached to a sturdy plastic handle, allowing for precise control during cleaning.

Unlike cotton swabs, foam-tipped swabs don’t shed fibers or leave lint behind — making them ideal for sensitive electronics, cleanrooms, and manufacturing environments.

Common Uses of Foam Swabs in Electronics

Foam swabs serve multiple cleaning functions across various industries, especially electronics. Here are some of their most popular applications:

• Cleaning circuit boards and connectors – Perfect for removing dirt and residue from hard-to-reach areas.
• Applying and removing adhesives – Helps evenly spread or safely remove adhesive without leaving streaks.
• Polishing components – Useful for shining metallic and plastic electronic surfaces.
• Dust removal – Ideal for gently cleaning keyboards, sensors, and optical equipment.

By selecting the correct type of foam swab, you can maintain your electronics’ performance and appearance with ease.

Types of Foam Swabs

Different shapes of foam swabs are designed to suit specific cleaning needs:

1. Flat Foam Swabs: Ideal for cleaning large or flat areas — such as touchscreens and instrument panels.
2. Pointed Foam Swabs: Perfect for precision cleaning of corners or tight spaces in circuit boards.
3. Round Foam Swabs: Handy for cleaning curved or delicate surfaces.
4. Cylindrical Foam Swabs: Suitable for cleaning internal ports, lenses, and rounded components.

Meditech offers a full range of these foam swab designs, available in various sizes and foam densities to fit nearly any electronic cleaning task.

How to Choose the Right Foam Swab for Electronics

Selecting the right foam swab ensures safe and effective cleaning. Below are critical factors to consider:

1. Size and Shape

Ensure the swab size fits the components you need to clean. A small, pointed swab is better for tight spaces, while a flat swab covers larger areas efficiently.

2. Material

Opt for non-abrasive materials such as polyurethane or polyester foam to avoid scratching delicate surfaces. The foam should also be chemical-resistant if you’re using it with cleaning solutions.

3. Absorbency

A highly absorbent foam can hold more cleaning agent, which reduces waste and enhances cleaning efficiency.

4. Cleanliness

Always use swabs that are lint-free and contaminant-free. Any dirt or oil on the swab can damage components rather than clean them.

5. Compatibility

Ensure your foam swab is compatible with your cleaning solution. Some foams may deteriorate when exposed to alcohol-based cleaners or solvents.

Why Choose Meditech Cleanroom Foam Swabs?

Meditech cleanroom foam swabs are trusted globally for their durability, precision, and contamination control. They are produced in ISO-certified cleanrooms and designed to meet the demands of electronics, biotechnology, and optical industries.

Key Benefits:

• Lint-free, non-abrasive polyurethane foam
• Excellent solvent resistance
• Precision-molded tips for consistent performance
• Compatible with IPA, acetone, and DI water
• Available in multiple head shapes and handle lengths

If you value precision, quality, and reliability, Meditech foam swabs are the smart choice.

In this guide, we’ll walk you through the step-by-step cleaning process for Zebra P430i and P330i printers so you can keep your machine in peak condition.

Why Cleaning Your Zebra P430i & P330i Printer Matters

Because card printers operate with high precision, even tiny amounts of dirt or residue can interfere with print quality. Regular cleaning ensures:

• Consistent, high-quality card printing
• Fewer card jams and misfeeds
• Protection of the print head from wear and damage
• Longer lifespan of internal components

While your printer will prompt you when cleaning is due, building a routine maintenance schedule will help you avoid downtime and costly repairs.

Step-by-Step Cleaning Instructions

Step 1: Start the Cleaning Cycle

• Leave the printer powered on.
• Hold down the front panel button until the LCD displays: “Remove ribbon and close head.”

Step 2: Remove the Ribbon

• Abra la tapa de la impresora.
• Push the blue release lever forward and lift the print head carriage.
• Remove both ribbon spools.
• Close the carriage.
• The LCD will then show: “Empty feeder and press button.”

Step 3: Prepare the Card Feeder

• Open the feeder cover.
• Remove all cards except the last one.
• Press the button to eject the bottom card safely.
• The display will read: “Load cleaning card in feeder.”

Step 4: Insert the Small Cleaning Card

• Take a small cleaning card from its pouch.
• Place it into the feeder; the belt will pull it halfway in automatically.
• Do not force the card.
• The printer will draw it through, cleaning the feeder and rollers.
• The LCD will read: “Cleaning printer.”
• Once complete, the card ejects and the display will show: “Press button to continue.”

Step 5: Use the Long Cleaning Card

• Open the long cleaning card package.
• Press the button until the LCD shows: “Feed long cleaning card in exit.”
• Insert the long card into the exit slot.
• The printer will move it back and forth to clean internal rollers.
• The LCD will again show: “Cleaning printer.”
• Once ejected, the printer returns to “Ready” status.

Step 6: Reload the Printer

• Reinsert the ribbon spools.
• Reload your card stack.
• The printer is now ready for use.

Step 7: Clean the Print Head (If Necessary)

If streaks or print issues remain after standard cleaning, manually clean the print head:

1. Turn the printer off.
2. Open the carriage and remove the ribbon.
3. Use a Zebra-approved cleaning swab (pre-saturated with cleaning solution).
4. Gently wipe the print head elements from side to side.
5. Let the head dry completely.
6. Reload the ribbon, power the printer back on, and resume printing.

By following these steps, your Zebra P430i and P330i printers will continue to deliver clear, professional-grade ID cards with minimal interruptions.

For optimal performance, use Meditech’s Zebra Cleaning Kits, designed specifically for P430i & P330i models. Regular use will not only keep your printer spotless but also extend its overall service life.

Step-by-Step Guide: How to Clean Zebra Printer Head with Snap Swab

Follow these simple steps to safely clean your Zebra printer head:

1. Turn the Printer Off
   Always power off your Zebra printer before cleaning to avoid damage.
2. Remove the Ribbon
   Lift the carriage and carefully take out the print ribbon.
3. Prepare the Snap Swab
   Squeeze the plastic stick of the cleaning swab until the liquid flows into the foam tip.
4. Clean the Print Head
   Gently move the moistened swab side to side across the print head elements. Avoid pressing too hard to protect the delicate surface.
5. Allow to Dry
   Wait a few minutes until the print head is completely dry.
6. Reinsert the Ribbon and Restart
   Place the ribbon spools back into the printer, close the carriage, and turn the printer on.

What If the Problem Persists?

If print quality issues continue after cleaning the printer head with a Snap Swab, the issue may be related to:

• Worn-out parts that need replacement
• Incorrect ribbon installation
• Mechanical problems within the printer

In these cases, check the Zebra printer user manual for troubleshooting steps or contact Zebra customer support for professional assistance.

For best results, we recommend using MediTech Snap Swabs, designed specifically for printer head cleaning. They are pre-saturated, easy to use, and safe for delicate print head elements.

Maintenance Accessory Needed

• Special adhesive cleaning card

We recommend using the MediTech Adhesive Cleaning Card, designed for professional printer cleaning and trusted by businesses worldwide.

Step-by-Step Guide to Cleaning the Primacy Lamination Module

1. Prepare the cleaning card
   Take the special adhesive cleaning card and carefully remove the two protective films from the front and back.
2. Check the lamination unit
   Ensure there is no film inside the lamination unit. If present, remove it gently before proceeding.
3. Launch the cleaning wizard
   Open Evolis Premium Suite® and start the lamination module cleaning wizard.
4. Insert the cleaning card
   Place the adhesive cleaning card into the opening located above the output hopper on the left-hand side of the printer.
5. Automatic cleaning process
   The card will automatically pass through the printer. The repeated movement inside the lamination module provides a deep clean, removing dust particles and film residue from the transport rollers.
6. Dispose of the used card
   Once the cleaning cycle is complete, the card will be ejected. Collect it and discard properly.
7. Reinstall the film
   Place the lamination film back into the unit and make sure it is positioned correctly.
8. Close the unit
   Shut the lamination unit door securely.
9. Printer ready to use
   Your Primacy Lamination card printer is now fully cleaned and ready for operation.

Why Regular Cleaning Is Important

• Prevents dust and film buildup
• Maintains consistent print quality
• Extends the life of your printer and consumables
• Reduces downtime and maintenance costs

By following this cleaning procedure, you ensure that your Primacy Lamination card printer continues to deliver professional results.

¿Con qué frecuencia debe limpiar su pistola?

La frecuencia de limpieza depende del uso, las condiciones ambientales y el tipo de munición. Como norma general:

• Después de cada sesión: Realiza una limpieza básica.
• Mensual o trimestral: Realice una inspección minuciosa y una limpieza a fondo si el arma no se ha utilizado.
• Inmediatamente: Limpiar después de la exposición a la lluvia, suciedad o munición corrosiva.

Herramientas y suministros esenciales para la limpieza de armas

Estos son los utensilios imprescindibles para una sesión de limpieza eficaz:

• Cepillo de púas: Afloja los residuos en el cañón.
• Varilla de limpieza o cable pasacables: Empuja los parches o bastoncillos de limpieza a través del cañón.
• Hisopos: Ideal para limpiar zonas estrechas como la recámara y la cara del cerrojo.
• Paño de limpieza: Perfecto para eliminar la carbonilla, la suciedad y el aceite de las superficies.
• Disolvente: Descompone la carbonilla y las incrustaciones.
• Lubricante: Reduce el desgaste y evita la corrosión.

Hisopo de limpieza recomendado:
Hisopos de espuma para salas blancas MediTech - Hisopos antiestáticos sin pelusa diseñados para la limpieza de precisión de zonas de difícil acceso en armas de fuego. Fabricados con espuma de alta calidad y mangos de polipropileno para un uso seguro y eficaz.

Paño de limpieza recomendado:
Toallitas de limpieza con IPA presaturado MediTech - Estas toallitas están presaturadas con alcohol isopropílico 70% o 99,9%, ideal para limpiar superficies de armas de fuego sin dejar pelusas ni residuos.

Proceso de limpieza de armas paso a paso

1. Descargar el arma de fuego

Compruebe siempre que el arma está completamente descargada antes de limpiarla.

2. Desmontaje según el manual

Desmonte el arma siguiendo las instrucciones del fabricante. Esto permite un mejor acceso a los componentes internos.

3. Limpiar el barril

Utilice un cepillo para taladros empapado en disolvente, seguido de parches secos o bastoncillos hasta que quede limpio. Termine con un parche ligeramente aceitado para proteger el interior.

Consejo: Utilice Hisopos de espuma MediTech para zonas delicadas del orificio o la cámara que requieren un toque suave sin rayar las superficies metálicas.

4. Limpiar otros componentes

Utilice bastoncillos y un paño de limpieza para limpiar la corredera, la recámara, el cerrojo y el compartimento del cargador. Concéntrese en eliminar la acumulación de carbono de los rincones estrechos.

En Toallitas de limpieza MediTech IPA son excelentes para limpiar superficies, sin dejar rayas ni residuos.

5. Lubricar las piezas móviles

Aplique una pequeña cantidad de aceite para armas a las bisagras, raíles y otras piezas móviles. Evite el exceso de lubricación, ya que puede atraer polvo y suciedad.

6. Volver a montar y limpiar

Vuelva a montar el arma y límpiela por última vez con un paño de limpieza limpio y seco para eliminar las huellas dactilares y el exceso de aceite.

Buenas prácticas y consejos

• Utilizar bastoncillos y toallitas sin pelusa para evitar residuos.
• Guarda tus productos de limpieza en un kit para mantenerse organizado.
• Llevar un registro de mantenimiento para cada arma de fuego.
• Inspeccionar en busca de desgaste regularmente.

Sin embargo, con el rápido desarrollo de la fabricación de productos electrónicos modernos, el desarrollo de bastoncillos de limpieza de este tipo de productos también son impulsados up.In la cara del mercado de una variedad de bastoncillos de limpieza, ¿cómo debemos hacer las elecciones?

En primer lugar, la elección de los hisopos debe centrarse en el material.Para hisopo de limpieza de cabeza de esponja,debe estar equipado con el excelente material de alta calidad,con las características de la fuerza fuerte de la limpieza,suave,flexibilidad,sin bordes duros,cabeza cayó migajas.Hisopos debe ser con de material no reactivos químicos añadidos,no hay que preocuparse por la reacción de los productos.No debe haber productos de silicona, al mismo tiempo,la cabeza no afecta al producto,tales como DVD y disco duro,etc.También debe cumplir con la norma Rohs, También debe cumplir con la norma Rohs.Pero una cosa se debe prestar atención a: cualquiera que diga que el hisopo de limpieza de la cabeza de la esponja puede cooperar con cualquier producto de limpieza disolvente que no son científicos.Debido a que cualquier buena esponja utilizada con acetona (acetona) solución producirá diferentes grados de "desfiguración" fenómeno.Pero en la vida real, la forma en que la gente usa hisopo cabeza de esponja es más común, por lo que puede considerar el uso de alcohol isopropílico (IPA) disolvente, su capacidad de limpieza y de protección del medio ambiente es muy excellent.If usted tiene que utilizar una mayor intensidad de disolventes de limpieza, tales como acetona (acetona),puede utilizar hisopos con cabeza de poliéster o fibra superfina(microfibra) cabeza, No sólo pueden lograr el efecto ideal, sino también hacer que la cabeza del hisopo sin "desfiguración".

En segundo lugar, los bastoncillos de exterior deben ser concisos, con buen tacto, y los mangos de los bastoncillos deben ser lisos, con buena flexibilidad, no fáciles de romper.De lo contrario, cualquier buen cabezal de bastoncillo no llegará a ninguna parte.Debido a que los bastoncillos son una especie de consumibles rápidos, por lo que el cabezal de bastoncillo en proceso de uso se ha consumido, por lo tanto, si los cabezales usados se pueden sustituir por cabezales de bastoncillo nuevos, será mucho mejor y eficaz.Y ahorrará el coste de la empresa, creemos que la mayoría de las empresas todavía piensan mucho en esta característica.

Por último, debemos elegir productos de fabricantes normales. Los productos de fabricantes normales no sólo pueden ofrecer un mejor servicio técnico y garantía de calidad, sino que también le aseguran una posición en el mercado con la ventaja de un precio competitivo.

En resumen, en cuanto a la elección de métodos de limpieza con hisopos o hisopos para limpieza de armas debemos prestar atención a los detalles del producto, su buena calidad y su valor económico y práctico.

Método uno: Utilice el kit de herramientas de impresión para limpiar el cabezal de inyección de tinta.

1. Haga clic en el botón de la parte inferior izquierda de su ordenador: "Inicio" → "Configuración" → "Impresión y fax" ,busque su tipo de impresora, haga clic con el botón derecho, elija "Preferencias de impresión".

2. En la ventana "Preferencias de impresión", haga clic en "Servicio" → "Mantener este dispositivo" y, a continuación, en el botón "Limpiar el cartucho de impresión" de la ventana emergente. O haga clic en "Función" → "Servicio de impresora" en la ventana "Preferencias de impresión".

3. Pulse el botón "Limpiar" en "Limpiar el cartucho de impresión".

4. El AIO empezará a imprimir la página de limpieza, y limpiará el cartucho automáticamente, hará un ruido de máquina desde el interior del AIO, hasta que la luz de encendido del AIO se encienda, y el sonido desaparezca, el proceso de limpieza habrá terminado.

Nota: Se consumirá algo de tinta al limpiar el cartucho. Normalmente, el ligero atasco del cabezal de inyección de tinta puede resolverse después de un proceso de limpieza. Si el cabezal de inyección de tinta está muy atascado, intente limpiarlo 1-2 veces, pero no más de 3 veces, ya que consumiría demasiada tinta.

Segundo método: Limpiar el contacto metálico del cartucho.

Si el cabezal de inyección de tinta tiene un mal contacto con el pedestal, afectará a la calidad de la impresión. Si se produce esta situación, intente limpiar el cabezal de inyección de tinta y el pedestal.

1. Extraiga el cabezal de inyección de tinta de la impresora.

2. Utilice un Hisopo de limpieza Meditech para limpiar el contacto eléctrico del pedestal del cabezal de inyección de tinta.

3. Utilice una toallita seca para limpiar el contacto eléctrico del cabezal de inyección de tinta. Sólo tiene que frotarlo una vez, ya que puede dañar el contacto eléctrico. No intente frotar el cabezal de inyección de tinta.

4. Vuelva a instalar el chorro de tinta.